SMC EliteConnect Wireless Bridge Guide de l'utilisateur Page 247
- Page / 318
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Wireless Interface Commands
7-99
7
Command Usage
• The normal 802.11a wireless operation mode provides connections up to
54 Mbps. Turbo Mode is an enhanced mode (not regulated in IEEE
802.11a) that provides a higher data rate of up to 108 Mbps. Enabling Turbo
Mode allows the access point to provide connections up to 108 Mbps.
• In normal mode, the access point provides a channel bandwidth of 20 MHz,
and supports the maximum number of channels permitted by local
regulations (e.g., 11 channels for the United States). In Turbo Mode, the
channel bandwidth is increased to 40 MHz to support the increased data
rate. However, this reduces the number of channels supported (e.g., 5
channels for the United States).
Example
multicast-data-rate
This command configures the maximum data rate at which the access point
transmits multicast and management packets (excluding beacon packets) on the
wireless interface.
Syntax
multicast-data-rate <speed>
speed - Maximum transmit speed allowed for multicast data.
(Options for 802.11a: 6, 12, 24 Mbps)
(Options for 802.11b/g; 1, 2, 5.5, 11 Mbps)
Default Setting
1 Mbps for 802.11b/g
6 Mbps for 802.11a
Command Mode
Interface Configuration (Wireless)
Example
SMC AP(if-wireless a)#turbo
SMC AP(if-wireless a)#
SMC AP(if-wireless g)#multicast-data-rate 5.5
SMC AP(if-wireless g)#
- USER GUIDE 1
- Copyright 3
- Compliances 4
- VCCI Notice 5
- EC Conformance Declaration 5
- Community 5
- Safety Compliance 7
- Power Cord Set 8
- (Germany): 10
- <BASEC> tragen 11
- Table of Contents 12
- Chapter 1: Introduction 20
- Package Checklist 21
- Hardware Description 21
- LED Indicators 22
- Introduction 23
- Ethernet Port 24
- Power Injector Module 24
- Grounding Point 25
- Water Tight Test Point 25
- Features and Benefits 26
- Access Point Topologies 27
- Infrastructure Wireless LAN 28
- Point-to-Point Configuration 30
- Bridge Link Topologies 31
- Network Configuration 32
- Data Rates 33
- Radio Path Planning 33
- Antenna Height 34
- Bridge Link Planning 36
- Radio Interference 37
- Weather Conditions 37
- Grounding 38
- Testing Basic Link Operation 39
- Mount the Unit 39
- Mounting on a Pole 40
- Mounting to a Wall 42
- Connect External Antennas 43
- Connect Cables to the Unit 44
- Ground Wire 45
- Ethernet Cable 45
- Grounding Screw 45
- Align Antennas 46
- Hardware Installation 48
- Required Connections 49
- Initial Configuration Steps 50
- Logging In 51
- Initial Configuration 52
- Advanced Configuration 54
- System Identification 55
- TCP / IP Settings 57
- SSH Settings 63
- Authentication 64
- Filter Control 69
- WDS Settings 73
- AP Management 79
- Administration 80
- Upgrading Firmware 81
- System Log 85
- Configuring SNTP 87
- Configuring SNMPv3 Users 98
- System Configuration 100
- Configuring SNMPv3 Targets 102
- Radio Interface 103
- Radio Settings A (802.11a) 105
- Normal Mode 111
- Turbo Mode 111
- Configuring Wi-Fi Multimedia 114
- Radio Settings G (802.11g) 120
- Security 122
- Enabling the VAPs 127
- Wi-Fi Protected Access (WPA) 133
- Configuring 802.1X 138
- Status Information 140
- Station Status 143
- Event Logs 145
- STP Status 147
- Chapter 7: Co 149
- Entering Commands 150
- Command Completion 151
- Getting Help on Commands 151
- Showing Commands 151
- SMC AP#show s? 152
- SMC AP#show s 152
- Exec Commands 153
- Configuration Commands 153
- Command Groups 154
- General Commands 155
- Command Line Interface 156
- System Management Commands 159
- APmgmtIP 169
- APmgmtUI 170
- System Logging Commands 177
- System Clock Commands 182
- DHCP Relay Commands 187
- SNMP Commands 189
- Flash/File Commands 204
- RADIUS Client 208
- 802.1X Authentication 214
- 802.1x session-timeout 216
- 802.1x-supplicant enable 217
- 802.1x-supplicant user 217
- MAC Address Authentication 219
- Filtering Commands 222
- WDS Bridge Commands 226
- Spanning Tree Commands 233
- Ethernet Interface Commands 238
- Wireless Interface Commands 243
- Rogue AP Detection Commands 264
- Wireless Security Commands 268
- Link Integrity Commands 278
- IAPP Commands 282
- VLAN Commands 283
- WMM Commands 285
- Appendix A: Troubleshooting 289
- Troubleshooting 290
- 10/100BASE-TX Pin Assignments 291
- Straight-Through Wiring 292
- Crossover Wiring 293
- 8-Pin DIN Connector Pinout 293
- Cables and Pinouts 294
- General Specifications 295
- Specifications 296
- Sensitivity 298
- Transmit Power 299
- V-förmige Halterung 301
- Montieren der Bridge 302
- Ethernet-Kabel 307
- Erdungsleitung 307
- Glossary 309
- Model Number: SMC2890W-AG / 317
- SMC2891W-AG 317
- Pub. Number: 149100034900E 317
- SMC2890W-AG / 318
© 2020, manymanuals.fr. Tous droits réservés | 0.067 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels